Payment & Shipping Terms:
|Materail:||Galvanized Steel Sheet||Contactor:||Fuji Brand|
|Copper Pipe Thick:||1 Mm||Compressor:||ZW Series ,With Crank Heating|
|Working Temperature:||-20--45 Degree||Insulation:||Foam Pack Pipe And Stick On The Machine Innner|
Super low noise heat pump high efficienty heating water fast heating electronic controller system . R407A / R417A / R404A Refrigerant
1 Rated heating capacity : 16KW
2 Hot water supply : 380L / h
3 Average heating input power :4KW
4 Rated heating input current : 9A
5 Max outlet water temp : 60℃
6 COP : 4.2
7 Power : 380V/50HZ
8 Noise : 48Dba ( a )
9 Dimension W*D*H : 1200*700*1360mm
10 packing size W*D*H : 1280*780*1420mm
11 weight : 160KG
12 Working air temp range : (-25℃)—45℃
13 compressor : Copeland
14 Air source heat exchanger : Finned heat exchange
Fan Type : Centrifugal fan
14 Hot water side heat exchange : Coil heat exchanger
Water flow :M6/H 5000L/h
15 Water pressure down :45Kpa
16 Pipe size : 25DN
1.meeting ultra - low temperature heating heat pump adopts EVI ultra-low temperature compressor and high - efficiency and environment-friendly refrigerant suitable for cold regions in the north, and the heating effect is 20 % - 40 % higher than that of conventional units under low temperature conditions, and the equipment will not decrease with the ambient temperature. Reduce the amount of heat, fully guarantee the effect of heating.
2 , meeting ultra-low temperature heating heat pump can be used normally below 0 °C, the minimum can be normal operation at -25 °C , and -20 °C energy efficiency ratio up to 2.0 or more , is our company exports to Europe for the heating of the flagship product, in Eastern, Western Europe, Northern Europe and other ten countries are used for indoor heating in the winter and spring seasons. It is also an energy-saving product that is very suitable for heating in northern China . It is used as a room heating in a cold area alone or as a heating device for heating needs .
A . Payment service
1 . T/T
2 . L/C (for container order only)
B . Technical service
1 . We calculate the capacity and recommend the best models.
2 . We supply you the professional refrigeration technical support and electronic technical support for your installation, debugging and operation.
3 . We supply the spare parts and technical support in and after the warranty time.
4 . We supply the training course to your workers at our factory if you need.
5 . We can offer site training to your workers in your place which is negotiable.
C. After-sales service
1. Technical support for your installation, operation and maintenance .
2. Standard warranty time : One years’warranty for heat pumps
You can also pay for extended warranty or we can renegotiate the longer warranty period .
Spare parts and technical support at most economic prices after the warranty.
1. Complying with ISO standard. Quality Ensured.
2. Complete Inspection for each unit before out of factory, covering water system and electricity detection and testing, ensuring 100% right product before shipment.
3. Strict quality control during production. We have liquid soap detection, halogen detection, electrical detection and water-soaking detection during production to avoid gas leakage and electrical problems .
4. Full inspection on bigger parts such as compressors, condensers, evaporators, expansion valves, flow switches, controllers etc.. Selection inspection for small parts such as sensors, pressure switches etc..
5. Well noise control by using mute cotton for casing plates and soft rubber feet for floating compressors, some of the models use compressor isolation shields.
6. Well insulated with insulated cotton for every pipe and parts, include compressor, dryer filter and each pipes.
7. We have passed TUV and SGS inspections. We have CE, RoHs, IEC, CCC, CB certificates for most of our products. Some of our products have en14511 test, en14825 test.
Q1. Can I have a sample order for Heat pump or Water tank?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A: Sample needs 3-10days, mass production time depend on the products'quantity.
Q3. Do you offer guarantee for the products?
A: Yes, 12 months since the heat pump depart from the port of loading (Refer to the Bill of Lading).
Certificate we have got :
1> ISO 9001, ISO 14000
2> Our company has been inspected and certificate by EMC
3> CE And EN14511, EN 14825-ERP for heat pump exported to Europe
4> Energy label for all heat pump models sold to oversea market
5> Testing laboratory calibrated by CNAS